| Excalibur® DAP 6456 Digital Access Product |
|
|
Economical WAN Access for Routers
The Excalibur® Digital Access Product (DAP) 6456 digital service unit (DSU) provides a
versatile, easy-to-use interface between your data terminal equipment (DTE) and digital
data service networks. The unit is specifically designed to provide economical WAN access
for routers. It supports synchronous data transmission over full-duplex channels at speeds
of 56 and 64 Kbps...providing efficient and economical performance.
Choice of Digital Data Service
The DAP 6456 offers the versatility to change between services as your needs and tariffs
change. You can select 56 Kbps Basic DDS or Clear Channel 64 Kbps service.
Automatic Service and Line Rate
Detection
The unit's service and line speed can be set automatically or manually via DIP switches.
With automatic detection enabled, the unit automatically configures itself to match the
type of service to which it is connected.
Easy to Install and Use
The DAP 6456 is designed to make installation, operation, and maintenance easy for even
the most non-technical user. The unit can be quickly installed with simple cable and power
connections. Configuration parameters are minimal. All configuration and diagnostic
parameters can be set in a minute via four DIP switches located on the front of the unit.
Fast and Easy Fault Isolation
Diagnostic tests allow you to quickly isolate the source of network malfunctions.
Available tests include local digital loopback and remote V.54 loopback. The DAP 6456
supports CSU loopback, latching loopback, and non-latching loopback tests initiated by the
network. Additionally, the unit automatically runs an internal self-test each time it is
powered up.
Instant Status Monitoring
Five LED indicators, located on the front of the unit, allow you to monitor the DAP 6456's
operating status at a glance. The LEDs inform you when power is applied to the unit, when
a loopback test is active, and when an alarm condition is present.
Compact Size
The standalone DAP 6456's compact size keeps space requirements to a bare minimum. The
unit is powered by a small external power supply, which can be easily replaced if
required.
Typical Excalibur DAP 6456 Application
Excalibur™ DAP 6456 Technical Specifications
| Line Requirements | Operates on 56 Kbps Basic DDS and Clear Channel 64 Kbps services |
| Network Configurations | Basic DDS Service: point-to-point and multipoint Clear Channel 64 Kbps Service: point-to-point |
| DTE Speeds | Synchronous: 56 and 64 Kbps |
| DTE Interface | V.35 |
| Channel Interface | 8-position keyed modular jack |
| Receiver Sensitivity | 0 to 45 dB loop loss |
| Carrier Mode | Constant, switched |
| Clocking | Slave, external |
| Tests | Self, local digital loopback, remote V.54 digital loopback |
| Network Diagnostics | CSU loopback, latching loopback, non-latching loopback |
| LED Indicators | Power, loss of signal (LOS), receive data, transmit data, loop |
| Approvals | FCC Part 15 and Part 68, Industry Canada, UL and CSA approved |
| Power Supply | External, 120 VAC, 60 Hz |
| Physical Specifications | Height: 1.50 inches (3.81 cm) Width: 4.94 inches ( 12.55 cm) Depth: 5.19 inches (13.18 cm) |
| Environmental | Operating Temperature: 32° to 122° F (0° to 50° C) Storage Temperature: -40° to 158° F (-40° to 70° C) Humidity: 10% to 95%, noncondensing |
Our policy of continuous development may cause the information and specifications contained herein to change without notice.
Excalibur is a registered trademark of Milgo Solutions. All other logos and product names are trademarks or registered trademarks of their respective companies.
©1999 Milgo Solutions. All rights reserved. Printed in
U.S.A.
